Raspberry Pi 3 --- Kernel Building and Run in A New Version Kernal

ABSTRACT

　　There are two main methods for building the kernel. You can build locally on a Raspberry Pi which will take a long time; or you can cross-compile, which is much quicker.There is an introduction about cross-compilation as follows.

　　You need ubuntu as your development environment.So you can install VMWare on Windows and install ubuntu on VMWare.

　　This link is the introduction from the official website :  https://www.raspberrypi.org/documentation/linux/kernel/building.md

CROSS COMPILING：

　　Download the cross compiling tools. 

　　$ mkdir raspberry      //make a folder for use

　　$ cd ./raspberry

　　$ git clone https://github.com/raspberrypi/tools     // make a folder named "tools" in the "raspberry"

　　

　　Add the following directory "/home/god/Desktop/raspberry/tools/arm-bcm2708/gcc-linaro-arm-linux-gnueabihf-raspbian-x64/bin" to your $PATH in the .bashrc as a environment variable.For the 32-bit host systems,the directory is "/home/god/Desktop/raspberry/tools/arm-bcm2708/gcc-linaro-arm-linux-gnueabihf-raspbian/bin".If you put the path to your account rather than "root",you had better execute the following in your account.Otherwise you will be reminded that command not found.

　　$ sudo apt-get install gcc-arm-linux-gnueabihf      //if execute it, you can use this gcc-linaro-arm-linux-gnueabihf version,not the version downloaded from "https://github.com/raspberrypi/tools".

GET SOURCE:

　　Enter the folder named "raspberry" ,then download the source:

　　$ git clone --depth=1 https://github.com/raspberrypi/linux   //make a folder named "linux" in the "raspberry"

　　The paramenter "--depth=1" means only downloading the lastest version

BUILD SOURCE:

　　$ cd ./linux

　　$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- bcm2709_defconfig   //bcm2709_defconfig做爲一個輸入參數給makefile，而後經過標準路徑「arch/arm/configs/」獲得bcm2709_defconfig這個文件，進而把一些參數複製給.config文件，

 

 

　　$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- zImage modules dtbs  //generate zImage,modules and dtbs

 

　　To speed up compilation on multiprocessor systems, and get some improvement on single processor ones, use -j n where n is number of processors * 1.5. Alternatively, feel free to experiment and see what works!

 

 

INSTALL ON THE SD CARD:

　　Having built the kernel you need to copy it onto your raspberry pi and install modules.This is the best done directly using an sd card reader.

　　Use lsblk before and after plugging in your sd card to identify which one is.

　　$ lsblk

　　$ mkdir /mnt/fat32

　　$ mkdir /mnt/ext4

　　$ mount /dev/sdc1 /mnt/fat32     //for example sdc1 is the FAT(boot) partition

　　$ mount /dev/sdc2 /mnt/ext4      //for example sdc2 is the ext3 filesystem(root) partition

　　execute the orders before enter the folder of "linux"

　　$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- INSTALL_MOD_PATH=/mnt/ext4 modules_install   //install the modules into the "lib/modules/XXXX" folder

　　Finally, copy the kernel and Device Tree blobs onto the SD card, making sure to back up your old kernel:

　　$ KERNEL=kernel7       //for Pi2 or 3, the kernel file is "kernel7.img" but for Pi 1,the kernel file is "kernel.img".So use "$KERNEL" to replace "kernel7"

　　$ cp /mnt/fat32/$KERNEL.img /mnt/fat32/$KERNEL-backup.img

　　$ scripts/mkknlimg arch/arm/boot/zImage /mnt/fat32/$KERNEL.img   //zImage is a Compressed kernel image,need transfer to .img

　　$ cp arch/arm/boot/dts/*.dtb /mnt/fat32/

　　$ cp arch/arm/boot/dts/overlays/*.dtb* /mnt/fat32/overlays/

　　$ cp arch/arm/boot/dts/overlays/README /mnt/fat32/overlays/

　　$ umount /mnt/fat32

　　$ umount /mnt/ext4

FINALLY

　　plug the SD card into Pi and boot it.