CCNP(BSCI)實驗：基礎IPv6實驗

第一步：配置各路由器的接口IPv6地址
R1(config)#int s2/1
R1(config-if)#ipv6 add 2001:1::/64 eui-64
R1(config-if)#no sh
R1(config-if)#int lo0
R1(config-if)#ipv6 add 1::1/64

R2(config)#int s2/1
R2(config-if)#ipv6 add 2001:1::1/64 eui-64
R2(config-if)#no sh
R2(config-if)#int lo0
R2(config-if)#ipv6 add 2::1/64
第二步：配置IPv6的靜態路由
R1(config)#ipv route 2::1/64 s2/1
R2(config)#ipv route 1::1/64 s2/1
第三步：查看IPv6路由
R1# sh ipv rou
IPv6 Routing Table - 7 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C 1::/64 [0/0]
via ::, Loopback0
L 1::1/128 [0/0]
via ::, Loopback0
S 2::/64 [1/0]
via ::, Serial2/1
C 2001:1::/64 [0/0]
via ::, Serial2/1
L 2001:1::C891:BFF:FE4C:0/128 [0/0]
via ::, Serial2/1
L FE80::/10 [0/0]
via ::, Null0
L FF00::/8 [0/0]
via ::, Null0

R2#sh ipv rou
IPv6 Routing Table - 7 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
S 1::/64 [1/0]
via ::, Serial2/1
C 2::/64 [0/0]
via ::, Loopback0
L 2::1/128 [0/0]
via ::, Loopback0
C 2001:1::/64 [0/0]
via ::, Serial2/1
L 2001:1::C892:EFF:FE64:0/128 [0/0]
via ::, Serial2/1
L FE80::/10 [0/0]
via ::, Null0
L FF00::/8 [0/0]
via ::, Null0

第四步：調試過程
R2#debug ipv packet
IPv6 unicast packet debugging is on
R2#ping 1::1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/29/44 ms