IPV6組網實驗
實驗目的：網絡
掌握IPV6網絡的配置和組建。dom
實驗環境拓撲圖及要求： 
ide
要求：oop
利用靜態路由協議實現全網互通測試
利用OSPF路由協議實現全網互通3d
備 注：【可選】router
寫出你在實驗中遇到的問題或者是新的發現或者新的解決方法（心得體會）blog
參考配置：進程
配置RIP:ip
ROUTER(config)#ipv6 router rip benet
ROUTER(config-rtr)#int e0/0
ROUTER(config-if)#ipv6 rip benet enable
ROUTER(config-if)#int lo1
ROUTER(config-if)#ipv6 rip benet enable
配置OSPF:
ROUTER(config)#ipv6 router ospf 100
ROUTER(config-rtr)#router-id 1.1.1.1(必須人爲指定router-id)
ROUTER(config-rtr)#int e0/0
ROUTER(config-if)#ipv6 ospf 100 area 1
ROUTER(config-rtr)#int lo1
ROUTER(config-if)#ipv6 ospf 100 area 1
配置文檔：
R1:
en
conf t
host R1
no ip domain-lo
int f0/0
ipv6 address 2001:2::1/64
no sh
exit
int loop 0
ipv6 address 2001:1::1/64
exit
ipv6 unicast-routing
ipv6 router ospf 10
router-id 1.1.1.1
int f0/0
ipv6 ospf 10 area 0
int loop 0
ipv6 ospf 10 area 0
end
--------------------------------------
R2:
en
conf t
host R2
no ip domain-lo
int f0/0
ipv6 address 2001:2::2/64
no sh
exit
int f1/0
ipv6 address 2001:3::1/64
no sh
exit
ipv6 unicast-routing
ipv6 router ospf 10
router-id 1.1.1.2
int f0/0
ipv6 ospf 10 area 0
int f1/0
ipv6 ospf 10 area 1
end
--------------------------------------
R3:
en
conf t
host R3
no ip domain-lo
int f0/0 //配置端口的IPV6地址
ipv6 address 2001:3::2/64
no sh
exit
int loop 0 //配置lo的IPV6地址
ipv6 address 2001:4::1/64
exit
ipv6 unicast-routing
ipv6 router ospf 10 //啓動ospf並配置其進程號
router-id 1.1.1.3 //配置router-ID
int f0/0
ipv6 ospf 10 area 1 //將端口映射到OSPF的區域1上
int loop 0
ipv6 ospf 10 area 1
end
--------------------------------------
測試截圖：
![clip_image002[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711807uaaA.jpg "clip_image002[4]")
![clip_image004[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711814Ph1C.jpg "clip_image004[4]")
![clip_image006[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711818eQvs.jpg "clip_image006[4]")
![clip_image008[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711825LXNA.jpg "clip_image008[4]")
![clip_image010[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_12677118296rlA.jpg "clip_image010[4]")
配置靜態路由：
ipv6 route 2008:DDDD::/64 Serial1/0
配置文檔：
R1:
en
conf t
host R1
no ip domain-lo
int f0/0
ipv6 address 2001:2::1/64
no sh
exit
int loop 0
ipv6 address 2001:1::1/64
exit
ipv6 unicast-routing
ipv6 route 2001:2::/64 2001:2::2
ipv6 route 2001:3::/64 2001:2::2
ipv6 route 2001:4::/64 2001:2::2
end
--------------------------------------
R2:
en
conf t
host R2
no ip domain-lo
int f0/0
ipv6 address 2001:2::2/64
no sh
exit
int f1/0
ipv6 address 2001:3::1/64
no sh
exit
ipv6 unicast-routing //配置IPV6的流量轉發
ipv6 route 2001:2::/64 2001:2::1 //配置靜態路由
ipv6 route 2001:1::/64 2001:2::1
ipv6 route 2001:3::/64 2001:3::2
ipv6 route 2001:4::/64 2001:3::2
end
--------------------------------------
R3:
en
conf t
host R3
no ip domain-lo
int f0/0
ipv6 address 2001:3::2/64
no sh
exit
int loop 0
ipv6 address 2001:4::1/64
exit
ipv6 unicast-routing
ipv6 route 2001:3::/64 2001:3::1
ipv6 route 2001:2::/64 2001:3::1
ipv6 route 2001:1::/64 2001:3::1
end
--------------------------------------
測試截圖：
![clip_image012[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711839H406.jpg "clip_image012[4]")
![clip_image014[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711847CiR4.jpg "clip_image014[4]")
![clip_image016[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711854erL1.jpg "clip_image016[4]")
![clip_image018[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_12677118619fRm.jpg "clip_image018[4]")
配置默認路由：
ipv6 route ::/0 Serial1/0
配置文檔：
R1:
en
conf t
host R1
no ip domain-lo
int f0/0
ipv6 address 2001:2::1/64
no sh
exit
int loop 0
ipv6 address 2001:1::1/64
exit
ipv6 unicast-routing
ipv6 route ::/0 2001:2::2 //配置IPV6默認路由
end
--------------------------------------
R2:
en
conf t
host R2
no ip domain-lo
int f0/0
ipv6 address 2001:2::2/64
no sh
exit
int f1/0
ipv6 address 2001:3::1/64
no sh
exit
ipv6 unicast-routing
ipv6 route ::/0 2001:2::1
ipv6 route ::/0 2001:3::2
end
--------------------------------------
R3:
en
conf t
host R3
no ip domain-lo
int f0/0
ipv6 address 2001:3::2/64
no sh
exit
int loop 0
ipv6 address 2001:4::1/64
exit
ipv6 unicast-routing
ipv6 route ::/0 2001:3::1
end
--------------------------------------
測試截圖：
![clip_image020[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711868S9e4.jpg "clip_image020[4]")
![clip_image022[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711875zUgm.jpg "clip_image022[4]")
![clip_image024[4]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711879uXIy.jpg "clip_image024[4]")
![clip_image002[6]](/link?url=https://s1.51cto.com/attachment/201003/4/771853_1267711885ckLj.jpg "clip_image002[6]")
- 1. IPV6實驗
- 2. ipv6實驗
- 3. IPV6隧道實驗
- 4. CCNP(BSCI)實驗：配置ISIS ipv6實驗
- 5. CCNP(BSCI)實驗：基礎IPv6實驗
- 6. ipV6實驗——華爲設備
- 7. IPV6 6to4,BGP綜合實驗
- 8. IPv6實驗MTU和PMTU
- 9. CCNP(BSCI)實驗：IPv6 EIGRP
- 10. Active Directory組網實驗
- 更多相關文章...
- • Web 網頁 驗證 - 網站建設指南
- • XML 驗證 - XML 教程
- • 互聯網組織的未來：剖析GitHub員工的任性之源
- • ☆基於Java Instrument的Agent實現
-
每一个你不满意的现在，都有一个你没有努力的曾经。
- 1. No provider available from registry 127.0.0.1:2181 for service com.ddbuy.ser 解決方法
- 2. Qt5.7以上調用虛擬鍵盤(支持中文)，以及源碼修改(可拖動，水平縮放)
- 3. 軟件測試面試- 購物車功能測試用例設計
- 4. ElasticSearch（概念篇）：你知道的, 爲了搜索…
- 5. redux理解
- 6. gitee創建第一個項目
- 7. 支持向量機之硬間隔（一步步推導，通俗易懂）
- 8. Mysql 異步複製延遲的原因及解決方案
- 9. 如何在運行SEPM配置嚮導時將不可認的複雜數據庫密碼改爲簡單密碼
- 10. windows系統下tftp服務器使用
- 1. IPV6實驗
- 2. ipv6實驗
- 3. IPV6隧道實驗
- 4. CCNP(BSCI)實驗：配置ISIS ipv6實驗
- 5. CCNP(BSCI)實驗：基礎IPv6實驗
- 6. ipV6實驗——華爲設備
- 7. IPV6 6to4,BGP綜合實驗
- 8. IPv6實驗MTU和PMTU
- 9. CCNP(BSCI)實驗：IPv6 EIGRP
- 10. Active Directory組網實驗