1-NET UX1000-實戰-配置-Lync Server 2010-集成

1-NET UX1000-實戰-配置-Lync Server 2010-集成

1. 實驗目的

FXS Quick Start 1.1

Configuring a call for the UX1000 FXS

Use the following step to configure a UX 1000 FXS Port.

Lync 分機----呼叫---FXS分機

8288------6001

FXS分機----呼叫--- Lync 分機

6001----8288

2. 登陸-UX1000

https://192.168.1.147

用戶名:admin

密 碼:admin

3. 驗證UX版本

Verifying the UX Versions

Prerequisite! Check your software level.

Verify that your UX1000 is loaded with firmware (boot partition) 2.1.6k and software p_w_picpath 2.0.0v108 or better.  Older versions of

firmware/software will cause the FXS card to not function.

To begin the configuration, verify your Boot and Application versions.

3.1. 選擇-Settings

3.2. 選擇-System-Software Management-Boot Partition

3.3. 選擇-System-Software Management-Application Partitions

Warning! Upgrade the UXSBA first.

If the UX application p_w_picpath requires an upgrade, always upgrade the UX Communication Service software (UXSBA) before upgrading

the UX application software. The firmware (boot) p_w_picpath can be upgraded either before or after the UX application software.

3.4. 驗證-許可證

Verify Licensing

The system must have the FXS and DSP licenses to make calls.  Depending upon the types of calls, the Transcoding license may also be necessary.

Unlimited---無限

SIP Registrations---註冊普通的SIP話機

支持註冊Skype

4. 驗證-FXS卡/端口狀態

Verify the FXS Card/Port State

Check to ensure that the FXS card and ports are functional by checking the System Tab | Overview Tab.  The FXS Telco modules should show Activated, and the Service and Admin States should be UP.

Main Board:主板

FXS Not Activated and Up?

Did you upgrade the firmware and software?

5. 配置-UX1000 For FXS

Configuring the UX1000 for FXS

5.1. 增長-配置文件

Begin the configuration by adding a CAS Signaling Profile for FXS.

選擇-Add FXS

選擇-OK

首先得創建配置文件。

FXS Profile---S口的配置文件。

5.2. 增長-默認路由表

增長

Default Route Table

5.3. 增長-信令組

add a CAS Signaling Group

ISDN SG:---數字線路-信令組

SIP SG:-----IP-信令組---鏈接Lync Server 2010

CAS SG:----針對模擬線路，S口和O口

選擇-Add CAS SG

Make sure to set the Channel Hunting to Own Number, otherwise the first free channel will answer every call (regardless of any other configuration settings).

參照:

Description:FXS Port 1

Channel Hunting:Own Number

Call Routing Table:Default Route Table

選擇-OK

5.4. 分配號到-S口

Add an Assigned Channel and apply the desired phone number to the corresponding FXS port.

增長

Apply

The FXS-attached phone should now have dial-tone.

No dial-tone?

Are you certain your firmware and software are updated as noted at the beginning of these instructions?

5.5. 增長-一個FXS口呼叫的交換

Lync > FXS

FXS > PSTN

5.6. Lync 服務器

SIP

Add

Signaling Groups

5.7. 路由表

注意---更正---Lync > FXS

注意轉換規則:

Lync > FXS

應用

應用

5.8. 測試

Lync---FXS

8288---6001

FXS---Lync

6001---8288

5.9.

6. 安裝-jre-6u30-windows-i586-s.exe

7. 監控-通話

訪問-NET UX1000

https://192.168.1.147

admin

admin

R是S口那邊沒掛斷，正常掛斷後不是這個樣子。是綠色。

8. 安裝-NET LX 2.8

NET LX 2.8---日誌管理

9. UX1000-設置

10. 日誌管理

10.1.打開-管理平臺

10.2.選擇-Syslog Server

10.3.選擇-Start Listering

10.4.Lync分機---呼叫---FXS口

8288---》---6001

10.5.接聽

10.6.選擇-Stop Listering

10.7.選擇-分析

10.8.

11. Lync分機---呼叫---FXS口分機

11.1.SIP

SIP Server Tables

填寫:

Lync Server 2010-服務器

192.168.1.82 5068

SIP Options

11.2.CAS

新建-FXS---分機配置文件

FXS Profile

11.3.Signaling Groups

信令組

CAS SG CAS信令組

寫入FXS口---分機號

SIP SG SIP信令組

寫入 SIP服務器

FX0---也須要建信令組.需實戰

E1----也須要建信令組.需實戰

11.4.Transformation

轉換規則

11.5.Call Routing Table