動態路由——OSPF虛鏈路配置實驗篇（五）

時間 2019-11-05

標籤動態路由 ospf 鏈路配置實驗欄目系統網絡简体版

原文原文鏈接

搭建OSPF虛鏈路實驗

搭建虛鏈路拓撲圖

再GNS 3中拓撲區域添加四臺路由設備，兩臺PC機，使用鏈接線，鏈接四臺路由設備與兩臺PC機，並再拓撲圖中標註鏈接接口的IP地址與區域信息，如圖所示：ide

網段劃分：

192.168.10.0/24
192.168.20.0/24
192.168.30.0/24
192.168.40.0/24
192.168.50.0/24

區域劃分：

area 0
area 1
area 2

Router ID劃分：

R1：1.1.1.1
R2 ：2.2.2.2
R3：3.3.3.3
R4：4.4.4.4

搭建實驗：

一、首先開啓在GNS 3中開啓所有設備，並進入R1路由設備中配置接口IP地址，設置迴環網卡，配置OSPF協議。oop

R1#conf t                     //進入全局配置模式
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#int f0/0            //進入f0/0接口
R1(config-if)#ip add 192.168.10.1 255.255.255.0     //添加IP地址
R1(config-if)#no shut            //開啓接口
R1(config-if)#
*Mar  1 00:00:50.995: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:00:51.995: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#int f0/1              //進入f0/1接口
R1(config-if)#ip add 192.168.20.1 255.255.255.0        //添加IP地址
R1(config-if)#no shut            //開啓接口
R1(config-if)#
*Mar  1 00:07:41.143: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar  1 00:07:42.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R1(config-if)#ex               //退出接口模式
R1(config)#int loopback 0       //進入配置迴環網卡
R1(config-if)#
*Mar  1 00:09:25.479: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R1(config-if)#ip add 1.1.1.1 255.255.255.255    //添加固定迴環網卡IP地址
R1(config-if)#no shut            //開啓接口
R1(config-if)#ex               //退出接口模式
R1(config)#router ospf 1        //開啓ospf協議，進程號爲1
R1(config-router)#router-id 1.1.1.1    //設置宣告Router ID
R1(config-router)#network 192.168.10.0 0.0.0.255 area 2    //宣告網段信息
R1(config-router)#network 192.168.20.0 0.0.0.255 area 2
R1(config-router)#
*Mar  1 00:15:16.883: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on FastEthernet0/1 from LOADING to FULL, Loading Done
R1(config-router)#ex             //退出接口模式

二、進入R2路由設置，配置接口IP地址，設置迴環網卡，配置OSPF協議。學習

R2#conf t                            //進入全局配置模式
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#int f0/0            //進入f0/0接口
R2(config-if)#ip add 192.168.20.2 255.255.255.0     //添加IP地址
R2(config-if)#no shut            //開啓接口
R2(config-if)#
*Mar  1 00:12:37.643: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:12:38.643: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config-if)#int f0/1              //進入f0/1接口
R2(config-if)#ip add 192.168.30.1 255.255.255.0        //添加IP地址
R2(config-if)#no shut            //開啓接口
R2(config-if)#
*Mar  1 00:13:06.051: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar  1 00:13:07.051: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R2(config-if)#ex               //退出接口模式
R2(config)#int loopback 0      //進入配置迴環網卡
R2(config-if)#
*Mar  1 00:13:54.103: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R2(config-if)#ip add 2.2.2.2 255.255.255.255    //添加固定迴環網卡IP地址
R2(config-if)#no shut            //開啓接口
R2(config-if)#ex               //退出接口模式
R2(config)#router ospf 1       //開啓ospf協議，進程號爲1
R2(config-router)#router-id 2.2.2.2    //設置宣告Router ID
R2(config-router)#network 192.168.20.1 0.0.0.255 area 2    //宣告網段信息
R2(config-router)#
*Mar  1 00:15:16.887: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
R2(config-router)#network 192.168.30.1 0.0.0.255 area 1 
R2(config-router)#ex             //退出接口模式

三、進入R3路由設置，配置接口IP地址，設置迴環網卡，配置OSPF協議。code

R3#conf t                            //進入全局配置模式
Enter configuration commands, one per line.  End with CNTL/Z.
R3(config)#int f0/0            //進入f0/0接口
R3(config-if)#ip add 192.168.30.2 255.255.255.0     //添加IP地址
R3(config-if)#no shut            //開啓接口
R3(config-if)#
*Mar  1 00:16:24.835: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:16:25.835: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R3(config-if)#int f0/1              //進入f0/1接口
R3(config-if)#ip add 192.168.40.1 255.255.255.0        //添加IP地址 
R3(config-if)#no shut            //開啓接口
R3(config-if)#
*Mar  1 00:16:56.135: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar  1 00:16:57.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R3(config-if)#ex              //退出接口模式
R3(config)#int loopback 0     //進入配置迴環網卡
R3(config-if)#ip 
*Mar  1 00:17:10.871: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R3(config-if)#ip add 3.3.3.3 255.255.255.255     //添加固定迴環網卡IP地址              
R3(config-if)#no shut           //開啓接口
R3(config-if)#ex               //退出接口模式
R3(config)#router ospf 1       //開啓ospf協議，進程號爲1
R3(config-router)#router-id 3.3.3.3    //設置宣告Router ID
R3(config-router)#network 192.168.30.0 0.0.0.255 area 1    //宣告網段信息
R3(config-router)#
*Mar  1 00:19:16.383: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
R3(config-router)#network 192.168.40.0 0.0.0.255 area 0
R3(config-router)#ex             //退出接口模式

四、進入R4路由設置，配置接口IP地址，設置迴環網卡，配置OSPF協議。router

R4#conf t                             //進入全局配置模式
Enter configuration commands, one per line.  End with CNTL/Z.
R4(config)#int f0/0            //進入f0/0接口
R4(config-if)#ip add 192.168.40.2 255.255.255.0     //添加IP地址
R4(config-if)#no shut            //開啓接口
R4(config-if)#
*Mar  1 00:20:26.999: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:20:27.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R4(config-if)#int f0/1              //進入f0/1接口
R4(config-if)#ip add 192.168.50.1 255.255.255.0        //添加IP地址 
R4(config-if)#no shut            //開啓接口
R4(config-if)#
*Mar  1 00:20:51.107: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar  1 00:20:52.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R4(config-if)#ex              //退出接口模式
R4(config)#int loopback 0     //進入配置迴環網卡
R4(config-if)#
*Mar  1 00:21:07.103: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R4(config-if)#ip add 4.4.4.4 255.255.255.255     //添加固定迴環網卡IP地址          
R4(config-if)#no shut           //開啓接口
R4(config-if)#ex               //退出接口模式
R4(config)#router ospf 1       //開啓ospf協議，進程號爲1
R4(config-router)#router-id 4.4.4.4    //設置宣告Router ID
R4(config-router)#network 192.168.40.0 0.0.0.255 area 0    //宣告網段信息
R4(config-router)#network 192.168.50.0 0.0.0.255 area 0

五、查看各路由設備路由表信息。blog

R1(config)#do show ip route         //查看R1設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
C    192.168.10.0/24 is directly connected, FastEthernet0/0
C    192.168.20.0/24 is directly connected, FastEthernet0/1        //未徹底學到所有網段信息

R2(config)#do show ip route         //查看R2設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     2.0.0.0/32 is subnetted, 1 subnets
C       2.2.2.2 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/1
O    192.168.10.0/24 [110/20] via 192.168.20.1, 00:09:31, FastEthernet0/0
O IA 192.168.40.0/24 [110/20] via 192.168.30.2, 00:05:30, FastEthernet0/1
C    192.168.20.0/24 is directly connected, FastEthernet0/0
O IA 192.168.50.0/24 [110/30] via 192.168.30.2, 00:02:26, FastEthernet0/1        //成功學習網段信息

R3(config)#do show ip route         //查看R3設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     3.0.0.0/32 is subnetted, 1 subnets
C       3.3.3.3 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.40.0/24 is directly connected, FastEthernet0/1
O    192.168.50.0/24 [110/20] via 192.168.40.2, 00:02:39, FastEthernet0/1        //未徹底學到所有網段信息

R4(config)#do show ip route         //查看R4設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

O IA 192.168.30.0/24 [110/20] via 192.168.40.1, 00:02:57, FastEthernet0/0
     4.0.0.0/32 is subnetted, 1 subnets
C      （1） 4.4.4.4 is directly connected, Loopback0    //添加（1）避免違禁詞彙
C    192.168.40.0/24 is directly connected, FastEthernet0/0
C    192.168.50.0/24 is directly connected, FastEthernet0/1        //未徹底學到所有網段信息

六、建立R二、R3路由設備中配置虛鏈路，是全部路由設備能夠學到所有網段信息；而後在查看路由設備路由表信息。接口

R2(config)#router ospf 1        //進入ospf協議
R2(config-router)#area 1 virtual-link 3.3.3.3       //配置虛鏈路鏈接R3路由設備

R3(config)#router ospf 1               //進入ospf協議
R3(config-router)#area 1 virtual-link 2.2.2.2       //配置虛鏈路鏈接R2路由設備
R3(config-router)#
*Mar  1 01:03:14.947: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on OSPF_VL0 from LOADING to FULL, Loading Done

R1(config)#do show ip route               //查看R1路由設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
O IA 192.168.30.0/24 [110/20] via 192.168.20.2, 00:05:19, FastEthernet0/1
C    192.168.10.0/24 is directly connected, FastEthernet0/0
O IA 192.168.40.0/24 [110/30] via 192.168.20.2, 00:03:36, FastEthernet0/1
C    192.168.20.0/24 is directly connected, FastEthernet0/1
O IA 192.168.50.0/24 [110/40] via 192.168.20.2, 00:03:36, FastEthernet0/1        //成功學習網段信息

R3(config)#do show ip route               //查看R3路由設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     3.0.0.0/32 is subnetted, 1 subnets
C       3.3.3.3 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/0
O IA 192.168.10.0/24 [110/30] via 192.168.30.1, 00:04:06, FastEthernet0/0
C    192.168.40.0/24 is directly connected, FastEthernet0/1
O IA 192.168.20.0/24 [110/20] via 192.168.30.1, 00:04:06, FastEthernet0/0
O    192.168.50.0/24 [110/20] via 192.168.40.2, 00:44:50, FastEthernet0/1        //成功學習網段信息

R4(config)#do show ip route               //查看R4路由設備路由表信息
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

O IA 192.168.30.0/24 [110/20] via 192.168.40.1, 00:45:36, FastEthernet0/0
     4.0.0.0/32 is subnetted, 1 subnets
C      （1） 4.4.4.4 is directly connected, Loopback0    //添加（1）避免違禁詞彙
O IA 192.168.10.0/24 [110/40] via 192.168.40.1, 00:04:43, FastEthernet0/0
C    192.168.40.0/24 is directly connected, FastEthernet0/0
O IA 192.168.20.0/24 [110/30] via 192.168.40.1, 00:04:43, FastEthernet0/0
C    192.168.50.0/24 is directly connected, FastEthernet0/1        //成功學習網段信息

七、在兩臺PC機中添加IP地址，並使用ping命令檢查互通性。進程

PC1> ip 192.168.10.2 192.168.10.1         //添加IP地址
Checking for duplicate address...
PC1 : 192.168.10.2 255.255.255.0 gateway 192.168.10.1

PC2> ip 192.168.50.2 192.168.50.1         //添加IP地址
Checking for duplicate address...
PC1 : 192.168.50.2 255.255.255.0 gateway 192.168.50.1

PC1> ping 192.168.50.2                   //使用ping命令與PC2通訊
192.168.50.2 icmp_seq=1 timeout
84 bytes from 192.168.50.2 icmp_seq=2 ttl=60 time=78.779 ms
84 bytes from 192.168.50.2 icmp_seq=3 ttl=60 time=77.795 ms
84 bytes from 192.168.50.2 icmp_seq=4 ttl=60 time=81.932 ms
84 bytes from 192.168.50.2 icmp_seq=5 ttl=60 time=83.226 ms       //成功通訊