traceroute學習

以前只知道ping telnet命令，後面學習了traceroute命令

ping最經常使用的，看是否能夠ping通ip，查看網絡是否可達

telnet探測端口是否通，telnet ip port

traceroute則是查看到達另一個主機中間經過的路由，尤爲是在主機不可達時，看到達哪一個路由後阻塞了，

Options:
  -4                          Use IPv4
  -6                          Use IPv6
  -d  --debug                 Enable socket level debugging
  -F  --dont-fragment         Do not fragment packets
  -f first_ttl  --first=first_ttl
                              Start from the first_ttl hop (instead from 1)
  -g gate,...  --gateway=gate,...
                              Route packets through the specified gateway
                              (maximum 8 for IPv4 and 127 for IPv6)
  -I  --icmp                  Use ICMP ECHO for tracerouting
  -T  --tcp                   Use TCP SYN for tracerouting
  -i device  --interface=device
                              Specify a network interface to operate with
  -m max_ttl  --max-hops=max_ttl
                              Set the max number of hops (max TTL to be
                              reached). Default is 30
  -N squeries  --sim-queries=squeries
                              Set the number of probes to be tried
                              simultaneously (default is 16)
  -n                          Do not resolve IP addresses to their domain names
  -p port  --port=port        Set the destination port to use. It is either
                              initial udp port value for "default" method
                              (incremented by each probe, default is 33434), or
                              initial seq for "icmp" (incremented as well,
                              default from 1), or some constant destination
                              port for other methods (with default of 80 for
                              "tcp", 53 for "udp", etc.)
  -t tos  --tos=tos           Set the TOS (IPv4 type of service) or TC (IPv6
                              traffic class) value for outgoing packets
  -l flow_label  --flowlabel=flow_label
                              Use specified flow_label for IPv6 packets
  -w waittime  --wait=waittime
                              Set the number of seconds to wait for response to
                              a probe (default is 5.0). Non-integer (float
                              point) values allowed too
  -q nqueries  --queries=nqueries
                              Set the number of probes per each hop. Default is
                              3
  -r                          Bypass the normal routing and send directly to a
                              host on an attached network
  -s src_addr  --source=src_addr
                              Use source src_addr for outgoing packets
  -z sendwait  --sendwait=sendwait
                              Minimal time interval between probes (default 0).
                              If the value is more than 10, then it specifies a
                              number in milliseconds, else it is a number of
                              seconds (float point values allowed too)
  -e  --extensions            Show ICMP extensions (if present), including MPLS
  -A  --as-path-lookups       Perform AS path lookups in routing registries and
                              print results directly after the corresponding
                              addresses
  -M name  --module=name      Use specified module (either builtin or external)
                              for traceroute operations. Most methods have
                              their shortcuts (`-I' means `-M icmp' etc.)
  -O OPTS,...  --options=OPTS,...
                              Use module-specific option OPTS for the
                              traceroute module. Several OPTS allowed,
                              separated by comma. If OPTS is "help", print info
                              about available options
  --sport=num                 Use source port num for outgoing packets. Implies
                              `-N 1'
  -U  --udp                   Use UDP to particular port for tracerouting
                              (instead of increasing the port per each probe),
                              default port is 53
  -UL                         Use UDPLITE for tracerouting (default dest port
                              is 53)
  -P prot  --protocol=prot    Use raw packet of protocol prot for tracerouting
  --mtu                       Discover MTU along the path being traced. Implies
                              `-F -N 1'
  --back                      Guess the number of hops in the backward path and
                              print if it differs
  -V  --version               Print version info and exit
  --help                      Read this help and exit

例如：

探測到另外一臺主機通過的路由

traceroute  www.baidu.com（或者ip地址）

探測包使用的基本UDP端口設置6888

traceroute -p 6888 www.baidu.com

繞過正常的路由表，直接發送到網絡相連的主機

traceroute -r www.baidu.com