2018-05-10 systemctl 命令徹底指南

時間  2019-12-12
標籤 systemctl 命令 徹底 指南 简体版
原文   原文鏈接

整理自：https://www.linuxidc.com/Linux/2015-07/120833.htm，添加了目錄。python

 

目錄：linux

1、 Systemd初體驗和Systemctl基礎  
1 systemd --version 首先檢查你的系統中是否安裝有systemd並肯定當前安裝的版本
2 whereis systemd         
whereis systemctl		 檢查systemd和systemctl的二進制文件和庫文件的安裝位置
3 ps -eaf | grep [s]ystemd 檢查systemd是否運行
4 systemd-analyze 分析systemd啓動進程
5 systemd-analyze blame 分析啓動時各個進程花費的時間
6 systemd-analyze critical-chain 分析啓動時的關鍵鏈
7 systemctl list-unit-files 列出全部可用單元
8 systemctl list-units 列出全部運行中單元
9 systemctl --failed 列出全部失敗單元
10 systemctl is-enabled crond.service 檢查某個單元（如 cron.service）是否啓用
11 systemctl status firewalld.service 檢查某個單元或服務是否運行
2、 使用Systemctl控制並管理服務  
12 systemctl list-unit-files --type=service 列出全部服務（包括啓用的和禁用的）
13 systemctl start httpd.service
systemctl restart httpd.service
systemctl stop httpd.service
systemctl reload httpd.service
systemctl status httpd.service		 Linux中如何啓動、重啓、中止、重載服務以及檢查服務（如 httpd.service）狀態
14 systemctl is-active httpd.service
systemctl enable httpd.service
systemctl disable httpd.service		 如何激活服務並在啓動時啓用或禁用服務（即系統啓動時自動啓動服務）
15 systemctl mask httpd.service
systemctl unmask httpd.service		 如何屏蔽（讓它不能啓動）或顯示服務（如 httpd.service）
16 systemctl kill httpd 使用systemctl命令殺死服務
3、 使用Systemctl控制並管理掛載點  
17 systemctl list-unit-files --type=mount 列出全部系統掛載點
18 systemctl start tmp.mount
systemctl stop tmp.mount
systemctl restart tmp.mount
systemctl reload tmp.mount
systemctl status tmp.mount		 掛載、卸載、從新掛載、重載系統掛載點並檢查系統中掛載點狀態
19 systemctl is-active tmp.mount
systemctl enable tmp.mount
systemctl disable tmp.mount		 在啓動時激活、啓用或禁用掛載點（系統啓動時自動掛載）
20 systemctl mask tmp.mount
systemctl unmask tmp.mount		 在Linux中屏蔽（讓它不能啓用）或可見掛載點
4、 使用Systemctl控制並管理套接口  
21 systemctl list-unit-files --type=socket 列出全部可用系統套接口
22 systemctl start cups.socket
systemctl restart cups.socket
systemctl stop cups.socket
systemctl reload cups.socket
systemctl status cups.socket		 在Linux中啓動、重啓、中止、重載套接口並檢查其狀態
23 systemctl is-active cups.socket
systemctl enable cups.socket
systemctl disable cups.socket		 在啓動時激活套接口，並啓用或禁用它（系統啓動時自啓動）
24 systemctl mask cups.socket
systemctl unmask cups.socket		 屏蔽（使它不能啓動）或顯示套接口
5、 服務的CPU利用率（分配額）  
25 systemctl show -p CPUShares httpd.service 獲取當前某個服務的CPU分配額（如httpd）
26 systemctl set-property httpd.service CPUShares=2000
systemctl show -p CPUShares httpd.service
vi /etc/systemd/system/httpd.service.d/90-CPUShares.conf		 將某個服務（httpd.service）的CPU分配份額限制爲2000 CPUShares/
27 systemctl show httpd 檢查某個服務的全部配置細節
28 systemd-analyze critical-chain httpd.service 分析某個服務（httpd）的關鍵鏈
29 systemctl list-dependencies httpd.service 獲取某個服務（httpd）的依賴性列表
30 systemd-cgls 按等級列出控制組
31 systemd-cgtop 按CPU、內存、輸入和輸出列出控制組
6、 控制系統運行等級  
32 systemctl rescue 啓動系統救援模式
33 systemctl emergency 進入緊急模式
34 systemctl get-default 列出當前使用的運行等級
35 systemctl isolate runlevel5.target
或systemctl isolate graphical.target		 啓動運行等級5，即圖形模式
36 systemctl isolate runlevel3.target
或systemctl isolate multi-user.target		 啓動運行等級3，即多用戶模式（命令行模式）
37 systemctl set-default runlevel3.target
systemctl set-default runlevel5.target		 設置多用戶模式或圖形模式爲默認運行等級
38 systemctl reboot
systemctl halt
systemctl suspend
systemctl hibernate
systemctl hybrid-sleep		 重啓、中止、掛起、休眠系統或使系統進入混合睡眠

systemctl 命令徹底指南

Systemctl是一個systemd工具，主要負責控制systemd系統和服務管理器。web

Systemd是一個系統管理守護進程、工具和庫的集合，用於取代System V初始進程。Systemd的功能是用於集中管理和配置類UNIX系統。shell

在Linux生態系統中，Systemd被部署到了大多數的標準Linux發行版中，只有爲數很少的幾個發行版還沒有部署。Systemd一般是全部其它守護進程的父進程，但並不是老是如此。bash

Manage Linux Services Using Systemctl

使用Systemctl管理Linux服務session

本文旨在闡明在運行systemd的系統上「如何控制系統和服務」。ssh

 

1、Systemd初體驗和Systemctl基礎

 

1. 首先檢查你的系統中是否安裝有systemd並肯定當前安裝的版本

  1. # systemd --version
  2. systemd 215
  3. +PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR

上例中很清楚地代表，咱們安裝了215版本的systemd。socket

 

2. 檢查systemd和systemctl的二進制文件和庫文件的安裝位置

  1. # whereis systemd
  2. systemd:/usr/lib/systemd /etc/systemd /usr/share/systemd /usr/share/man/man1/systemd.1.gz
  3. # whereis systemctl
  4. systemctl:/usr/bin/systemctl /usr/share/man/man1/systemctl.1.gz

 

3. 檢查systemd是否運行

  1. # ps -eaf | grep [s]ystemd
  2. root 10016:27?00:00:00/usr/lib/systemd/systemd --switched-root --system --deserialize 23
  3. root 4441016:27?00:00:00/usr/lib/systemd/systemd-journald
  4. root 4691016:27?00:00:00/usr/lib/systemd/systemd-udevd
  5. root 5551016:27?00:00:00/usr/lib/systemd/systemd-logind
  6. dbus 5561016:27?00:00:00/bin/dbus-daemon --system --address=systemd:--nofork --nopidfile --systemd-activation

注意：systemd是做爲父進程（PID=1）運行的。在上面帶（-e）參數的ps命令輸出中，選擇全部進程，（-a）選擇除會話前導外的全部進程，並使用（-f）參數輸出完整格式列表（即 -eaf）。工具

也請注意上例中後隨的方括號和例子中剩餘部分。方括號表達式是grep的字符類表達式的一部分。post

 

4. 分析systemd啓動進程

  1. # systemd-analyze
  2. Startup finished in487ms(kernel)+2.776s(initrd)+20.229s(userspace)=23.493s

 

5. 分析啓動時各個進程花費的時間

  1. # systemd-analyze blame
  2. 8.565s mariadb.service
  3. 7.991s webmin.service
  4. 6.095s postfix.service
  5. 4.311s httpd.service
  6. 3.926s firewalld.service
  7. 3.780s kdump.service
  8. 3.238s tuned.service
  9. 1.712s network.service
  10. 1.394s lvm2-monitor.service
  11. 1.126s systemd-logind.service
  12. ....

 

6. 分析啓動時的關鍵鏈

  1. # systemd-analyze critical-chain
  2. The time after the unit is active or started is printed after the "@" character.
  3. The time the unit takes to start is printed after the "+" character.
  4. multi-user.target @20.222s
  5. └─mariadb.service @11.657s+8.565s
  6. └─network.target @11.168s
  7. └─network.service @9.456s+1.712s
  8. └─NetworkManager.service @8.858s+596ms
  9. └─firewalld.service @4.931s+3.926s
  10. └─basic.target @4.916s
  11. └─sockets.target @4.916s
  12. └─dbus.socket @4.916s
  13. └─sysinit.target @4.905s
  14. └─systemd-update-utmp.service @4.864s+39ms
  15. └─auditd.service @4.563s+301ms
  16. └─systemd-tmpfiles-setup.service @4.485s+69ms
  17. └─rhel-import-state.service @4.342s+142ms
  18. └─local-fs.target @4.324s
  19. └─boot.mount @4.286s+31ms
  20. └─systemd-fsck@dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d19608096
  21. └─dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d196080964.device@4

重要：Systemctl接受服務（.service），掛載點（.mount），套接口（.socket）和設備（.device）做爲單元。

 

7. 列出全部可用單元

  1. # systemctl list-unit-files
  2. UNIT FILE STATE
  3. proc-sys-fs-binfmt_misc.automount static
  4. dev-hugepages.mount static
  5. dev-mqueue.mount static
  6. proc-sys-fs-binfmt_misc.mount static
  7. sys-fs-fuse-connections.mount static
  8. sys-kernel-config.mount static
  9. sys-kernel-debug.mount static
  10. tmp.mount disabled
  11. brandbot.path disabled
  12. .....

 

8. 列出全部運行中單元

  1. # systemctl list-units
  2. UNIT LOAD ACTIVE SUB DESCRIPTION
  3. proc-sys-fs-binfmt_misc.automount loaded active waiting ArbitraryExecutableFileFormatsFileSyste
  4. sys-devices-pc...0-1:0:0:0-block-sr0.device loaded active plugged VBOX_CD-ROM
  5. sys-devices-pc...:00:03.0-net-enp0s3.device loaded active plugged PRO/1000 MT DesktopAdapter
  6. sys-devices-pc...00:05.0-sound-card0.device loaded active plugged 82801AA AC'97 Audio Controller
  7. sys-devices-pc...:0:0-block-sda-sda1.device loaded active plugged VBOX_HARDDISK
  8. sys-devices-pc...:0:0-block-sda-sda2.device loaded active plugged LVM PV Qzyo3l-qYaL-uRUa-Cjuk-pljo-qKtX-VgBQ8
  9. sys-devices-pc...0-2:0:0:0-block-sda.device loaded active plugged VBOX_HARDDISK
  10. sys-devices-pl...erial8250-tty-ttyS0.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS0
  11. sys-devices-pl...erial8250-tty-ttyS1.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS1
  12. sys-devices-pl...erial8250-tty-ttyS2.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS2
  13. sys-devices-pl...erial8250-tty-ttyS3.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS3
  14. sys-devices-virtual-block-dm\x2d0.device loaded active plugged /sys/devices/virtual/block/dm-0
  15. sys-devices-virtual-block-dm\x2d1.device loaded active plugged /sys/devices/virtual/block/dm-1
  16. sys-module-configfs.device loaded active plugged /sys/module/configfs
  17. ...

 

9. 列出全部失敗單元

  1. # systemctl --failed
  2. UNIT LOAD ACTIVE SUB DESCRIPTION
  3. kdump.service loaded failed failed Crash recovery kernel arming
  4. LOAD =Reflects whether the unit definition was properly loaded.
  5. ACTIVE =The high-level unit activation state, i.e. generalization of SUB.
  6. SUB =The low-level unit activation state, values depend on unit type.
  7. 1 loaded units listed.Pass--all to see loaded but inactive units, too.
  8. To show all installed unit files use'systemctl list-unit-files'.

 

10. 檢查某個單元（如 cron.service）是否啓用

  1. # systemctl is-enabled crond.service
  2. enabled

 

11. 檢查某個單元或服務是否運行

  1. # systemctl status firewalld.service
  2. firewalld.service - firewalld -dynamic firewall daemon
  3. Loaded: loaded (/usr/lib/systemd/system/firewalld.service; enabled)
  4. Active: active (running) since Tue2015-04-2816:27:55 IST;34min ago
  5. Main PID:549(firewalld)
  6. CGroup:/system.slice/firewalld.service
  7. └─549/usr/bin/python -Es/usr/sbin/firewalld --nofork --nopid
  8. Apr2816:27:51 tecmint systemd[1]:Starting firewalld -dynamic firewall daemon...
  9. Apr2816:27:55 tecmint systemd[1]:Started firewalld -dynamic firewall daemon.

 

2、使用Systemctl控制並管理服務

 

12. 列出全部服務（包括啓用的和禁用的）

  1. # systemctl list-unit-files --type=service
  2. UNIT FILE STATE
  3. arp-ethers.service disabled
  4. auditd.service enabled
  5. autovt@.service disabled
  6. blk-availability.service disabled
  7. brandbot.service static
  8. collectd.service disabled
  9. console-getty.service disabled
  10. console-shell.service disabled
  11. cpupower.service disabled
  12. crond.service enabled
  13. dbus-org.Fedoraproject.FirewallD1.service enabled
  14. ....

 

13. Linux中如何啓動、重啓、中止、重載服務以及檢查服務（如 httpd.service）狀態

  1. # systemctl start httpd.service
  2. # systemctl restart httpd.service
  3. # systemctl stop httpd.service
  4. # systemctl reload httpd.service
  5. # systemctl status httpd.service
  6. httpd.service -TheApache HTTP Server
  7. Loaded: loaded (/usr/lib/systemd/system/httpd.service; enabled)
  8. Active: active (running) since Tue2015-04-2817:21:30 IST;6s ago
  9. Process:2876ExecStop=/bin/kill -WINCH ${MAINPID}(code=exited, status=0/SUCCESS)
  10. Main PID:2881(httpd)
  11. Status:"Processing requests..."
  12. CGroup:/system.slice/httpd.service
  13. ├─2881/usr/sbin/httpd -DFOREGROUND
  14. ├─2884/usr/sbin/httpd -DFOREGROUND
  15. ├─2885/usr/sbin/httpd -DFOREGROUND
  16. ├─2886/usr/sbin/httpd -DFOREGROUND
  17. ├─2887/usr/sbin/httpd -DFOREGROUND
  18. └─2888/usr/sbin/httpd -DFOREGROUND
  19. Apr2817:21:30 tecmint systemd[1]:StartingTheApache HTTP Server...
  20. Apr2817:21:30 tecmint httpd[2881]: AH00558: httpd:Couldnot reliably determine the server's fully q...ssage
  21. Apr 28 17:21:30 tecmint systemd[1]: Started The Apache HTTP Server.
  22. Hint: Some lines were ellipsized, use -l to show in full.

注意：當咱們使用systemctl的start，restart，stop和reload命令時，咱們不會從終端獲取到任何輸出內容，只有status命令能夠打印輸出。

 

14. 如何激活服務並在啓動時啓用或禁用服務（即系統啓動時自動啓動服務）

  1. # systemctl is-active httpd.service
  2. # systemctl enable httpd.service
  3. # systemctl disable httpd.service

 

15. 如何屏蔽（讓它不能啓動）或顯示服務（如 httpd.service）

  1. # systemctl mask httpd.service
  2. ln -s '/dev/null''/etc/systemd/system/httpd.service'
  3. # systemctl unmask httpd.service
  4. rm '/etc/systemd/system/httpd.service'

 

16. 使用systemctl命令殺死服務

  1. # systemctl kill httpd
  2. # systemctl status httpd
  3. httpd.service -TheApache HTTP Server
  4. Loaded: loaded (/usr/lib/systemd/system/httpd.service; enabled)
  5. Active: failed (Result:exit-code) since Tue2015-04-2818:01:42 IST;28min ago
  6. Main PID:2881(code=exited, status=0/SUCCESS)
  7. Status:"Total requests: 0; Current requests/sec: 0; Current traffic: 0 B/sec"
  8. Apr2817:37:29 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  9. Apr2817:37:29 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  10. Apr2817:37:39 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  11. Apr2817:37:39 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  12. Apr2817:37:49 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  13. Apr2817:37:49 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  14. Apr2817:37:59 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  15. Apr2817:37:59 tecmint systemd[1]: httpd.service:Got notification message from PID 2881, but recepti...bled.
  16. Apr2818:01:42 tecmint systemd[1]: httpd.service: control process exited, code=exited status=226
  17. Apr2818:01:42 tecmint systemd[1]:Unit httpd.service entered failed state.
  18. Hint:Some lines were ellipsized,use-l to show in full.

 

3、使用Systemctl控制並管理掛載點

 

17. 列出全部系統掛載點

  1. # systemctl list-unit-files --type=mount
  2. UNIT FILE STATE
  3. dev-hugepages.mount static
  4. dev-mqueue.mount static
  5. proc-sys-fs-binfmt_misc.mount static
  6. sys-fs-fuse-connections.mount static
  7. sys-kernel-config.mount static
  8. sys-kernel-debug.mount static
  9. tmp.mount disabled

 

18. 掛載、卸載、從新掛載、重載系統掛載點並檢查系統中掛載點狀態

  1. # systemctl start tmp.mount
  2. # systemctl stop tmp.mount
  3. # systemctl restart tmp.mount
  4. # systemctl reload tmp.mount
  5. # systemctl status tmp.mount
  6. tmp.mount -TemporaryDirectory
  7. Loaded: loaded (/usr/lib/systemd/system/tmp.mount; disabled)
  8. Active: active (mounted) since Tue2015-04-2817:46:06 IST;2min48s ago
  9. Where:/tmp
  10. What: tmpfs
  11. Docs: man:hier(7)
  12. http://www.freedesktop.org/wiki/Software/systemd/APIFileSystems
  13. Process:3908ExecMount=/bin/mount tmpfs /tmp -t tmpfs -o mode=1777,strictatime (code=exited, status=0/SUCCESS)
  14. Apr2817:46:06 tecmint systemd[1]:MountingTemporaryDirectory...
  15. Apr2817:46:06 tecmint systemd[1]: tmp.mount:Directory/tmp to mount over isnot empty, mounting anyway.
  16. Apr2817:46:06 tecmint systemd[1]:MountedTemporaryDirectory.

 

19. 在啓動時激活、啓用或禁用掛載點（系統啓動時自動掛載）

  1. # systemctl is-active tmp.mount
  2. # systemctl enable tmp.mount
  3. # systemctl disable tmp.mount

 

20. 在Linux中屏蔽（讓它不能啓用）或可見掛載點

  1. # systemctl mask tmp.mount
  2. ln -s '/dev/null''/etc/systemd/system/tmp.mount'
  3. # systemctl unmask tmp.mount
  4. rm '/etc/systemd/system/tmp.mount'

 

4、使用Systemctl控制並管理套接口

 

21. 列出全部可用系統套接口

  1. # systemctl list-unit-files --type=socket
  2. UNIT FILE STATE
  3. dbus.socket static
  4. dm-event.socket enabled
  5. lvm2-lvmetad.socket enabled
  6. rsyncd.socket disabled
  7. sshd.socket disabled
  8. syslog.socket static
  9. systemd-initctl.socket static
  10. systemd-journald.socket static
  11. systemd-shutdownd.socket static
  12. systemd-udevd-control.socket static
  13. systemd-udevd-kernel.socket static
  14. 11 unit files listed.

 

22. 在Linux中啓動、重啓、中止、重載套接口並檢查其狀態

  1. # systemctl start cups.socket
  2. # systemctl restart cups.socket
  3. # systemctl stop cups.socket
  4. # systemctl reload cups.socket
  5. # systemctl status cups.socket
  6. cups.socket - CUPS PrintingServiceSockets
  7. Loaded: loaded (/usr/lib/systemd/system/cups.socket; enabled)
  8. Active: active (listening) since Tue2015-04-2818:10:59 IST;8s ago
  9. Listen:/var/run/cups/cups.sock (Stream)
  10. Apr2818:10:59 tecmint systemd[1]:Starting CUPS PrintingServiceSockets.
  11. Apr2818:10:59 tecmint systemd[1]:Listening on CUPS PrintingServiceSockets.

 

23. 在啓動時激活套接口，並啓用或禁用它（系統啓動時自啓動）

  1. # systemctl is-active cups.socket
  2. # systemctl enable cups.socket
  3. # systemctl disable cups.socket

 

24. 屏蔽（使它不能啓動）或顯示套接口

  1. # systemctl mask cups.socket
  2. ln -s '/dev/null''/etc/systemd/system/cups.socket'
  3. # systemctl unmask cups.socket
  4. rm '/etc/systemd/system/cups.socket'

 

5、服務的CPU利用率（分配額）

 

25. 獲取當前某個服務的CPU分配額（如httpd）

  1. # systemctl show -p CPUShares httpd.service
  2. CPUShares=1024

注意：各個服務的默認CPU分配份額=1024，你能夠增長/減小某個進程的CPU分配份額。

 

26. 將某個服務（httpd.service）的CPU分配份額限制爲2000 CPUShares/

  1. # systemctl set-property httpd.service CPUShares=2000
  2. # systemctl show -p CPUShares httpd.service
  3. CPUShares=2000

注意：當你爲某個服務設置CPUShares，會自動建立一個以服務名命名的目錄（如 httpd.service），裏面包含了一個名爲90-CPUShares.conf的文件，該文件含有CPUShare限制信息，你能夠經過如下方式查看該文件：

  1. # vi /etc/systemd/system/httpd.service.d/90-CPUShares.conf
  2. [Service]
  3. CPUShares=2000

 

27. 檢查某個服務的全部配置細節

  1. # systemctl show httpd
  2. Id=httpd.service
  3. Names=httpd.service
  4. Requires=basic.target
  5. Wants=system.slice
  6. WantedBy=multi-user.target
  7. Conflicts=shutdown.target
  8. Before=shutdown.target multi-user.target
  9. After=network.target remote-fs.target nss-lookup.target systemd-journald.socket basic.target system.slice
  10. Description=TheApache HTTP Server
  11. LoadState=loaded
  12. ActiveState=active
  13. SubState=running
  14. FragmentPath=/usr/lib/systemd/system/httpd.service
  15. ....

 

28. 分析某個服務（httpd）的關鍵鏈

  1. # systemd-analyze critical-chain httpd.service
  2. The time after the unit is active or started is printed after the "@" character.
  3. The time the unit takes to start is printed after the "+" character.
  4. httpd.service +142ms
  5. └─network.target @11.168s
  6. └─network.service @9.456s+1.712s
  7. └─NetworkManager.service @8.858s+596ms
  8. └─firewalld.service @4.931s+3.926s
  9. └─basic.target @4.916s
  10. └─sockets.target @4.916s
  11. └─dbus.socket @4.916s
  12. └─sysinit.target @4.905s
  13. └─systemd-update-utmp.service @4.864s+39ms
  14. └─auditd.service @4.563s+301ms
  15. └─systemd-tmpfiles-setup.service @4.485s+69ms
  16. └─rhel-import-state.service @4.342s+142ms
  17. └─local-fs.target @4.324s
  18. └─boot.mount @4.286s+31ms
  19. └─systemd-fsck@dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d196080964.service@4.092s+149ms
  20. └─dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d196080964.device@4.092s

 

29. 獲取某個服務（httpd）的依賴性列表

  1. # systemctl list-dependencies httpd.service
  2. httpd.service
  3. ├─system.slice
  4. └─basic.target
  5. ├─firewalld.service
  6. ├─microcode.service
  7. ├─rhel-autorelabel-mark.service
  8. ├─rhel-autorelabel.service
  9. ├─rhel-configure.service
  10. ├─rhel-dmesg.service
  11. ├─rhel-loadmodules.service
  12. ├─paths.target
  13. ├─slices.target
  14. │├─-.slice
  15. │└─system.slice
  16. ├─sockets.target
  17. │├─dbus.socket
  18. ....

 

30. 按等級列出控制組

  1. # systemd-cgls
  2. ├─1/usr/lib/systemd/systemd --switched-root --system --deserialize 23
  3. ├─user.slice
  4. │└─user-0.slice
  5. │└─session-1.scope
  6. │├─2498 sshd: root@pts/0
  7. │├─2500-bash
  8. │├─4521 systemd-cgls
  9. │└─4522 systemd-cgls
  10. └─system.slice
  11. ├─httpd.service
  12. │├─4440/usr/sbin/httpd -DFOREGROUND
  13. │├─4442/usr/sbin/httpd -DFOREGROUND
  14. │├─4443/usr/sbin/httpd -DFOREGROUND
  15. │├─4444/usr/sbin/httpd -DFOREGROUND
  16. │├─4445/usr/sbin/httpd -DFOREGROUND
  17. │└─4446/usr/sbin/httpd -DFOREGROUND
  18. ├─polkit.service
  19. │└─721/usr/lib/polkit-1/polkitd --no-debug
  20. ....

 

31. 按CPU、內存、輸入和輸出列出控制組

  1. # systemd-cgtop
  2. PathTasks%CPU MemoryInput/s Output/s
  3. /831.0437.8M--
  4. /system.slice -0.1---
  5. /system.slice/mariadb.service 20.1---
  6. /system.slice/tuned.service 10.0---
  7. /system.slice/httpd.service 60.0---
  8. /system.slice/NetworkManager.service 1----
  9. /system.slice/atop.service 1----
  10. /system.slice/atopacct.service 1----
  11. /system.slice/auditd.service 1----
  12. /system.slice/crond.service 1----
  13. /system.slice/dbus.service 1----
  14. /system.slice/firewalld.service 1----
  15. /system.slice/lvm2-lvmetad.service 1----
  16. /system.slice/polkit.service 1----
  17. /system.slice/postfix.service 3----
  18. /system.slice/rsyslog.service 1----
  19. /system.slice/system-getty.slice/getty@tty1.service 1----
  20. /system.slice/systemd-journald.service 1----
  21. /system.slice/systemd-logind.service 1----
  22. /system.slice/systemd-udevd.service 1----
  23. /system.slice/webmin.service 1----
  24. /user.slice/user-0.slice/session-1.scope3----

 

6、控制系統運行等級

 

32. 啓動系統救援模式

  1. # systemctl rescue
  2. Broadcast message from root@tecmint on pts/0(Wed2015-04-2911:31:18 IST):
  3. The system is going down to rescue mode NOW!

 

33. 進入緊急模式

  1. # systemctl emergency
  2. Welcome to emergency mode!After logging in, type "journalctl -xb" to view
  3. system logs,"systemctl reboot" to reboot,"systemctl default" to try again
  4. to boot intodefault mode.

 

34. 列出當前使用的運行等級

  1. # systemctl get-default
  2. multi-user.target

 

35. 啓動運行等級5，即圖形模式

  1. # systemctl isolate runlevel5.target
  2. 或
  3. # systemctl isolate graphical.target

 

36. 啓動運行等級3，即多用戶模式（命令行）

  1. # systemctl isolate runlevel3.target
  2. 或
  3. # systemctl isolate multiuser.target

 

37. 設置多用戶模式或圖形模式爲默認運行等級

  1. # systemctl set-default runlevel3.target
  2. # systemctl set-default runlevel5.target

 

38. 重啓、中止、掛起、休眠系統或使系統進入混合睡眠

  1. # systemctl reboot
  2. # systemctl halt
  3. # systemctl suspend
  4. # systemctl hibernate
  5. # systemctl hybrid-sleep

對於不知運行等級爲什麼物的人，說明以下。

  • Runlevel 0 : 關閉系統
  • Runlevel 1 : 救援？維護模式
  • Runlevel 3 : 多用戶，無圖形系統
  • Runlevel 4 : 多用戶，無圖形系統
  • Runlevel 5 : 多用戶，圖形化系統
  • Runlevel 6 : 關閉並重啓機器
相關文章
相關標籤/搜索
每日一句
    每一个你不满意的现在，都有一个你没有努力的曾经。
本站公眾號
   歡迎關注本站公眾號,獲取更多信息
聯繫我們 最近搜索 最新文章 沪ICP备13005482号-10 MyBatis教程 SQL 教程 MySQL教程 Java 教程 Thymeleaf 教程 Hibernate教程 Spring教程 Redis教程